2251 real customers worldwide
Technical Description of OBD-II Trouble Code
Leaking Fuel Injector in Cylinder 11
What does that signify?
This is a generic diagnostic trouble code (DTC) for the powertrain and is commonly found in OBD-II vehicles. This includes various vehicle makes and models. Although it is a generic code, the specific repair steps may differ depending on the year, make, model, and powertrain configuration.
If your OBD-II equipped vehicle has stored the code P02C5, it means that the powertrain control module (PCM) has detected a potential fuel injector leak in a specific cylinder of the engine, in this case, cylinder #11.
Automotive fuel injectors need to maintain a precise fuel pressure to deliver the correct amount of fuel in a precisely sprayed pattern to each cylinder’s combustion chamber. This precise pattern requires that each fuel injector is free from leaks and restrictions.
The PCM monitors factors such as fuel trim requirements, exhaust oxygen sensor data, crankshaft position, and camshaft position to identify a lean condition and determine which cylinder is experiencing a malfunction.
Data signals from the oxygen sensors inform the PCM about lean exhaust oxygen content and which bank of the engine is affected. Once a lean exhaust condition is identified in a specific bank of the engine, the position of the camshaft and crankshaft helps determine which injector is causing the issue. When the PCM confirms a lean condition and identifies the affected fuel injector in cylinder #11, it stores the code P02C5 and may illuminate the malfunction indicator lamp (MIL).
In some cases, multiple failure cycles may be required for the MIL to illuminate.
A cross section of a typical fuel injector:
What is the severity of this DTC?
A P02C5 code should be considered severe because a lean fuel condition could potentially cause damage to the cylinder head or engine.
What are some of the symptoms of the code?
Symptoms of a P02C5 trouble code may include:
What are some of the common causes of the code?
Possible causes for this P02C5 fuel injector code may include:
What are some P02C5 troubleshooting steps?
Before diagnosing a code P02C5, it is important to diagnose and repair any MAF and MAP related codes.
Start the diagnosis by inspecting the fuel injection rail area. Focus on the fuel injector in question (cylinder #11). Check for signs of corrosion or leakage on the exterior of the fuel injector. If there is significant corrosion or leakage, it is likely that the injector has failed.
If no obvious mechanical issues are found in the engine bay, several tools will be needed for an accurate diagnosis:
Next, connect the scanner to the vehicle’s diagnostic port and retrieve all stored codes and freeze frame data. This information will be helpful during the diagnosis. Clear the codes and test-drive the vehicle to see if the P02C5 code reappears.
If the code P02C5 immediately returns, use the scanner to perform an injector balance test to confirm that the misfire is caused by an injector problem. Once this is confirmed, proceed to step 1.
Step 1
With the engine running, use the stethoscope to listen to the fuel injector in question. You should hear a repeated clicking sound in a specific pattern. If there is no sound at all, proceed to step 2. If the sound is strained or intermittent, suspect that the injector for cylinder #11 has failed or is clogged. Compare the sounds from that cylinder’s injector to others for comparison, if necessary.
Step 2
Use the DVOM to test for voltage and a ground pulse while the engine is running. Most manufacturers use a system where one terminal of the fuel injector receives constant battery voltage, while the other terminal receives a ground pulse from the PCM at the appropriate time.
If no voltage is detected at the connector of the fuel injector in question, use the DVOM to test the system fuses and relays. Replace any blown fuses or faulty relays as needed.
It is recommended to test system fuses with the circuit under a load. A fuse that appears to be good when the circuit is not loaded (key on/engine off) may fail when the circuit is loaded (key on/engine running).
If all system fuses and relays are functioning properly and there is still no voltage, use the vehicle information source to trace the circuit back to the ignition switch or fuel injection module (if applicable).
Note: Exercise caution when testing/replacing high-pressure fuel system components.
Professional Service
While we always recommend resolving this issue through mechanical means, if that is not possible, we offer the option to permanently delete this specific DTC. All other codes will continue to be addressed. If you are interested in this option, please upload your ECU file to our portal.
