2251 real customers worldwide
Technical Description of OBD-II Trouble Code
The circuit for the reductant level sensor is registering a high reading.
What does that signify?
This is a standard diagnostic trouble code (DTC) for powertrain issues that is applicable to OBD-II vehicles. Various vehicle makes, including but not limited to BMW, Mercedes Benz, VW Volkswagen, Sprinter, Ford, Audi, Dodge, Ram, GMC, Chevrolet, Jeep, etc., may be affected.
Were you aware that the engine light illuminates when the engine’s exhaust emissions exceed the specified limits? The ECM (Engine control module) monitors and adjusts numerous sensors, valves, systems, etc. Essentially, it functions as an integrated emissions testing station. It not only monitors the intake of your engine but, more importantly for the manufacturer, it monitors what your engine is releasing into the atmosphere.
This is relevant in this context because reductant level sensors are primarily found in diesel-powered vehicles with a DEF (Diesel exhaust fluid) storage tank. DEF is a urea solution used in diesel engines to assist in burning exhaust, thereby reducing overall vehicle emissions, which, as mentioned earlier, is one of the ECM’s most important functions. The reductant level sensor communicates the DEF fluid level in its storage tank to the ECM.
P203D is the trouble code defined as “Reductant Level Sensor Circuit High” and indicates that the ECM has detected an unexpectedly high electrical reading from the sensor circuit.
A reductant DEF tank:
What is the severity of this DTC?
Considering the possibilities, I would classify this as a relatively minor code. Essentially, it refers to a fault in a system that monitors what happens after the exhaust has been burned and used. However, most states/countries have stringent emissions standards, so it is advisable to address this issue before it causes further harm to your vehicle and the environment!
What are some of the symptoms of the code?
The symptoms associated with a P203D diagnostic code may include:
What are some of the common causes of the code?
The causes of this P203D engine code may include:
What are some diagnostic and troubleshooting steps for P203D?
The initial step in the troubleshooting process for any malfunction is to consult the Technical Service Bulletins (TSB) for known issues specific to your vehicle.
Advanced diagnostic steps are highly vehicle-specific and may require specialized equipment and expertise for accurate execution. We have provided basic steps below, but it is recommended to refer to a vehicle year/make/model/powertrain specific repair guide for precise instructions pertaining to your vehicle.
Basic Step #1
Before diagnosing any present codes, ensure that all active codes have been completely cleared and test drive the vehicle. This will clear any codes that may have remained active after repairs or other intermittent, less significant codes. After the test drive, rescan the vehicle and proceed with diagnosis only if active codes are detected.
Basic Step #2
If you have owned your vehicle for a considerable period of time, you are likely aware of the location of the DEF (Diesel exhaust fluid) storage tank. If not, these tanks are typically located in the trunk or under the vehicle. The filler neck for the storage tank should be easily accessible, either in the trunk or next to the fuel filler neck. Prioritize identifying it to avoid introducing unwanted fluid into incorrect locations. If you can mechanically check the level with a dipstick, do so. However, some vehicles do not provide a means of verifying the DEF level other than visually inspecting the tank with a flashlight. In any case, it is advisable to top up the fluid, especially if P203F is also present.
Basic Step #3
If your OBD2 code reader/scan tool allows for electronic monitoring of the sensor, you may be able to do so. This is particularly relevant if you know that the storage tank is full of DEF and the reading is indicating otherwise. In such cases, it is likely that the reductant level sensor is defective and needs to be replaced. However, replacing the sensor can be challenging as it is mounted to the tank. Ensure that you catch any DEF that may spill out during the sensor replacement process.
Basic Step #4
If you can easily access the connector for the reductant level sensor, ensure that it is making a secure electrical connection. Additionally, it is always advisable to consult the manufacturer’s service data to obtain specific values and procedures for testing the level sensor to confirm its defectiveness before replacing it. This may involve resistance tests, for which a multimeter will likely be required. Compare the actual values to the desired ones provided by the manufacturer. If the values deviate from the specified range, the sensor will need to be replaced.
NOTE: Always adhere to the manufacturer’s guidelines regarding battery disconnection, safety precautions, etc.
Basic Step #5
Inspect the wiring harness of the reductant level sensor for any damage or exposed wires, as this can result in erratic values being transmitted to the ECM and potentially lead to unnecessary sensor replacement. Repair any bare wires or corrosion before proceeding. Ensure that the harness is securely fastened and kept away from any moving parts.
This article is intended solely for informational purposes, and it is always recommended to prioritize the technical data and service bulletins specific to your vehicle.
Professional Service
While we always recommend resolving this issue through mechanical means, if that is not feasible for any reason, we offer the option to permanently delete this specific DTC. All other codes will continue to be addressed. If you are interested in this service, please upload your ECU file to our portal.
